(813)750-0388 Book a Repair
Monogram microwave & advantium error code

Monogram Microwave SE: Touchpad Key Shorted or Stuck

SE on a Monogram microwave means one touchpad key is shorted or stuck down in the pressed position. It is closely related to F1 but reported through a different diagnostic path.

Needs attention soonChecked November 2026

What does Monogram microwave & advantium code SE mean?

SE tells you the control sees one touchpad key as pressed constantly, either through a short or because the key physically sticks. Closely related to F1, it comes up when a control platform reports the same problem along a different diagnostic route, so you may see SE where another unit shows F1. Moisture or residue on the keypad is a simple place to begin, and a failed touchpad is the other end of the range.

SE at a glance

Code
SE
Appliance
Monogram microwave & advantium
Applies to
Monogram microwave touchpad controls
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Moisture or residue bridging the contacts under a key

What you may notice with SE

  • SE appears on the display without any key press
  • The touchpad does not respond properly to other keys
  • A key looks stuck or feels sticky when pressed
  • The panel was recently wet or splashed with cleaner

How the microwave & advantium detects SE

A Monogram microwave reads its touchpad by scanning each key and noting which ones are pressed. Under normal use, a key reads as pressed only for a moment while you touch it. The control board expects every key to return to rest straight away.

SE is reported when one key keeps reading as pressed. A shorted contact, perhaps from moisture or residue under the key, produces the same signal as a finger that never lifts. A key that is physically stuck does it too, and so does a touchpad that has failed. Some control platforms present this through a different diagnostic path than F1, which is why SE and F1 are closely related. Wiping the panel is the simplest thing to rule out first.

Likely causes of SE

  • Moisture or residue bridging the contacts under a key
  • A key stuck in the pressed position
  • A touchpad that has failed

Can you keep using the microwave & advantium with SE?

Avoid running the microwave while SE is showing, because a key that reads as pressed can make the controls unreliable. Unplug it before wiping the panel. If wiping and a restart clear the code and the controls behave normally, you can use it again. If SE returns, leave it unused until it is checked.

What you can safely check

  1. Stop the microwave and unplug it, or switch off its breaker, so no key press can start it.
  2. Wipe the touchpad with a clean, dry or barely damp cloth, and dry it completely.
  3. Look for a key that sits down or looks raised or stuck.
  4. Restore power and watch whether SE returns.
  5. If it stays, call us.

What our technician does for SE

  • Check the touchpad for a shorted or stuck key
  • Test the touchpad connection to the control board
  • Replace the touchpad if it has failed

How to keep SE from coming back

  • Wipe the touchpad with a barely damp cloth, never spraying cleaner directly onto the keys.
  • Wipe up splashes and steam film promptly so moisture does not collect under the keys.
  • Humid Florida kitchens leave a film on touch panels, so dry the panel after cleaning.

Technical reference

Code
SE
Appliance
Monogram microwave & advantium
Control family
Monogram microwave touchpad controls
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

SE questions

Is SE the same as F1 on a Monogram microwave?

They are closely related. Both describe a key reading as pressed, but the code shown depends on the control platform and the diagnostic path it uses.

Can spilled liquid cause SE?

Moisture or residue on the keypad can short a key contact. A safe first step is to wipe the panel and let it dry fully, taking care not to push liquid into the controls.

Why does SE appear when I am not pressing anything?

The control sees one key as held down. That can be a shorted contact, a physically stuck key or a failed touchpad, so the microwave reports SE even without a press.

Will SE go away once the panel dries?

It can, if moisture or residue was shorting a key and the panel dries out. If SE returns once the panel is clean and dry, a key or the touchpad itself is the more likely cause.

What should I tell the technician about SE?

Say whether SE appeared after a spill or cleaning, whether any key feels stuck, and whether other keys respond. That helps decide between a surface problem and a failed touchpad.

Need help with SE?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair