(813)750-0388 Book a Repair
Common Problems · 5 min read

Monogram Built-In Ice Maker Making Little or Cloudy Ice

Monogram Built-In Ice Maker Making Little or Cloudy Ice

When a Monogram built-in ice maker produces little or cloudy ice, the cause is usually water: an old filter, a supply valve that is partly closed, a drain that is slow, or ice that has piled up in the bin. Work through those in order and the answer is often clear before anyone needs to open a panel.

Why is my ice maker making so little ice?

An ice maker can only freeze as much water as it receives. If the water filter is clogged, the supply line is kinked or the shutoff valve is only partly open, the tray fills slowly and each batch is small. A built-in unit also needs time to reach its freezing temperature after it is first started, and again after a power outage, so a weak first day is not always a problem.

The bin matters as well. Many Monogram ice makers have a sensor that stops production when the bin is full. If ice has clumped into a single block, the sensor may think the bin is full while most of the space is empty. Lifting out the scoop and breaking up the clump by hand with the machine off is a safe way to test this.

Why is the ice cloudy?

Cloudy ice usually means the water has air or dissolved minerals in it. In many parts of Tampa Bay the tap water carries minerals, and homes on private wells can see more of this. Clear ice is harder to make than cloudy ice, so a certain amount of cloudiness is simply how ice freezes. The problem begins when the ice is white, tastes odd or leaves a film on glasses.

A filter that is past its replacement time is the first suspect. After that, scale inside the unit can cloud the ice and slow the water flow. A Monogram unit with a drain and a water filter wants regular attention, particularly in a humid climate where mold and slime like to grow in damp spots.

What can you check yourself, safely?

Turn the ice maker off at its control or breaker first. Then look at the simple items:

  1. Find the water shutoff valve under the sink or behind the unit and make sure it is fully open.
  2. Check the water filter. If you cannot remember the last change, replace it with the filter listed in your use-and-care guide.
  3. Look at the visible water line for kinks, especially if the unit was pushed back during cleaning.
  4. Remove the ice, wash the bin with warm water and mild soap, and rinse it well before putting it back.
  5. Restart the unit and give it several hours before you judge the result.

If you see water on the floor, turn off the water supply before you do anything else. Do not reach into the machine while it is powered, and leave sealed refrigeration and the water inlet valve to a technician.

What you see Likely cause Owner check
Small or thin ice pieces Low water flow Open the shutoff valve fully and replace the filter
Bin looks empty, no new ice Bin sensor blocked by clumped ice Break up the clump and clear ice from the sensor area
Cloudy or white ice Minerals, air, or a worn filter Replace the filter and clean the bin
Ice tastes or smells off Old ice, odors or a dirty bin Discard the ice, clean the bin, replace the filter
Water pooling around the unit Slow drain or leaking line Shut off the water and keep the area dry

Could the drain or the water valve be the problem?

Yes. Many built-in ice makers melt a little ice and send the water out through a drain. If the drain line is partly blocked or crimped, water backs up, ice freezes together and production slows. In a Florida home, slime in drain lines is common because warm, damp conditions favor it. If you see standing water at the bottom of the bin or hear gurgling, the drain deserves a look.

The inlet valve is the part that opens to let water into the tray. When it wears out or is clogged with sediment, it can open only partly, and the unit makes small amounts of ice no matter how often you change the filter. This is a job for a technician, because the valve is connected to both the water supply and the electrical system.

Homes that were closed for months are a special case. If you spend part of the year elsewhere, the water line may have been sitting still, and the first batches of ice should be thrown out. Run the unit and discard the first few batches before you serve any.

When should you call a technician?

Call when the filter is new, the valve is open and the bin is clean, but ice is still scarce or cloudy. Call right away if you see water leaking, hear a running motor with no ice, or notice frost building up inside the unit. Those signs usually involve the water inlet, the drain, the temperature sensor or the cooling system.

When we service a Monogram ice maker, we check the water pressure, the inlet valve, the drain path, the bin sensor and the freezing temperature. We tell you what we found and quote the repair in writing before we begin work. If your ice maker sits on a covered lanai or in an outdoor kitchen, tell us, since heat, salt air and moisture add other things to look at.

Frequently asked questions

How often should I replace the water filter?

Follow the schedule in your use-and-care guide, and replace it sooner if flow slows or the ice tastes different. Homes with well water or heavy sediment may need changes more often. A filter that is overdue is one of the most common reasons for small, cloudy ice.

Is cloudy ice safe to use?

Cloudy ice from air or minerals is generally not harmful, but ice that smells, tastes odd or looks discolored should be thrown out. Clean the bin, replace the filter and run a few batches before using it again.

Why did my ice maker stop after a storm?

An outage can interrupt the freezing cycle, and a surge can upset the controls. Turn the unit off and on once after power returns, wait several hours, and check the bin. If it still does not produce ice, have it examined.

Can I use any filter that fits?

Use the filter named in your use-and-care guide. A filter that only looks similar can leak or restrict flow. Check your warranty terms if you are unsure, and ask us if you cannot find the right part.

Sources

Call Book a Repair
Call (813)750-0388 Book a Repair