(813)750-0388 Book a Repair
Common Problems · 4 min read

Monogram Gas Rangetop Burner Clicks But Will Not Light

Monogram Gas Rangetop Burner Clicks But Will Not Light

When a burner on a Monogram gas rangetop clicks but does not light, the cause is usually something simple: a burner cap that is out of place, a wet or dirty igniter, or clogged burner ports. If you smell gas at any time, leave the home immediately and call the gas utility or 911 from outside.

What should you do first if you smell gas?

Safety comes before troubleshooting. If you smell gas, do not turn on lights, do not touch switches, and do not use a phone inside the home. Leave right away, take everyone with you, and call your gas utility or 911 from outside. Do not go back in until you are told it is safe. Do not try to find the leak yourself.

If you do not smell gas but a burner has been clicking for a long time, turn all the knobs to off and wait a few minutes before you try again, so gas that has collected can clear. Never use a match or lighter on a burner that has stopped lighting unless your use-and-care guide describes it.

Why does the burner click and not light?

The clicking is the igniter sparking. It will click as long as the knob is in the light position, even if the gas is not reaching the burner correctly. When the spark does not catch, one of three things is usually the reason: the burner is not seated properly, the igniter is wet or dirty so the spark is weak, or the ports where the gas flows out are blocked.

A sealed burner on a rangetop depends on the cap and the base being aligned. If a cap sits slightly crooked after cleaning, the flame cannot form around it, and the burner may click for a long time. Lift the cap off and set it back down until it sits flat.

What can you check at home?

Turn all burners off and wait until the rangetop is fully cool. Then:

  1. Lift off the cap and the burner head and set them aside.
  2. Look at the igniter, the small ceramic nub beside the burner. If it is wet, dab it dry with a clean cloth.
  3. Check for boil-over residue. Wipe the area with a damp cloth and a little mild dish soap, and dry it well.
  4. Clear the ports with a soft brush or a straight pin or toothpick, without enlarging the holes.
  5. Dry the parts completely and put them back, making sure each one sits flat.

Do not remove the gas valve, the igniter wiring or any panel under the rangetop. Do not spray cleaner into the burner or onto the igniter, and do not use a wet cloth on a hot surface.

Sign Likely cause Owner check Next step
One burner clicks only Cap out of place or blocked ports Reseat the cap, clean the ports Call if it still will not light
Clicks start after cooking or cleaning Wet igniter Dry the igniter, wait and retry Call if it stays wet
All burners click and none light Gas supply or valve issue Check whether other gas appliances work Call, and call the utility if gas is off
Flame is yellow or uneven Dirty ports or poor air mix Clean the ports Call if it does not improve
Clicking continues after the flame is on Moisture or a sticking switch Dry the area, turn off and retry Call if it repeats

How does Florida humidity or weather matter?

Humidity and heavy rain can leave moisture around an igniter, especially on a rangetop in an outdoor kitchen or a covered lanai. Salt air near the coast can add corrosion over time. After a storm, a power surge can also upset the electronic igniter. If a burner will not light after an outage, turn all the knobs off, wait a few minutes, and try again.

A spill from a boiling pot is the most common thing that makes a burner click and fail. Soup, pasta water and sugar can fill the ports and wet the igniter in one go. Wiping up spills after the burner cools reduces repeat problems.

When is it time to call a technician?

Call when a burner still will not light after the cap is seated, the igniter is dry and the ports are clean. Call right away for a flame that lifts off the burner, a strong yellow flame, a gas smell, or a burner that keeps clicking by itself. Those signs involve the igniter, the spark module, the valve or the gas supply, all of which are work for a licensed technician.

We check the igniter, the spark module, the wiring, the gas pressure and the flame on each burner. We never bypass a safety device, and we will not leave a gas appliance in a condition we are not comfortable with.

Frequently asked questions

Can I light the burner with a match?

Do not, unless your use-and-care guide gives a specific method for your model. A match near a burner with gas flowing is a risk, and lighting it by hand only hides the reason the igniter is not working.

Why does one burner click when I use another?

Moisture or a sticking switch can send spark to burners that are not in use. Dry the area around the igniters, make sure the knobs are fully off, and call if the clicking continues.

Is it safe to keep cooking on the other burners?

If you do not smell gas and the other burners light normally, many owners do so until the visit. Turn off the one that fails, keep its knob off, and tell us about it when we schedule the repair.

How often should I clean the burners?

Wipe up spills after each use, once the surface is cool, and do a fuller cleaning of the caps and ports as your use-and-care guide describes. Regular cleaning prevents most lighting problems.

Sources

Call Book a Repair
Call (813)750-0388 Book a Repair