(813)750-0388 Book a Repair
Troubleshooting · 4 min read

Monogram Wine Reserve Display Shows HI, LO or an Alarm

Monogram Wine Reserve Display Shows HI, LO or an Alarm

When a Monogram wine reserve shows HI, LO or an alarm, the display is reporting that the temperature inside has moved away from the set temperature, or that something changed the cooling. Close the door fully, check that power is on, confirm the setpoint, and give it time. If the display stays on HI or LO, call.

What do HI and LO usually mean?

On many wine refrigeration displays, HI means the cabinet is warmer than the control is allowed to show or allow, and LO means it is colder. The wording on your display and what each one means for your model come from the use and care guide, so read that page before you decide what to do.

A reading is not the same as a failure. A door left open, a warm bottle load added all at once, or a recent power loss can push the temperature out of range for a time, and the display may clear on its own as the cabinet recovers.

Wine stores best at a steady temperature, so a drifting cabinet matters. Do not assume a bottle is fine or ruined from the reading alone. Use a separate thermometer placed on a shelf to see what the cabinet is actually doing.

Was the door left open or ajar?

Door alarms are the most common cause of an alarm message. A glass-front door looks closed when it is not sealing, and a bottle that leans against the glass, a rack shifted out of place or a loose label can keep it from shutting.

Open the door, look for anything touching the gasket or the frame, and close the door firmly. Watch the display for a minute. If the alarm clears, the door was the cause. In a Florida home where the room itself is warm, a door left open lets heat and humidity in and the compressor runs longer to recover.

Could power or the setpoint be the cause?

Summer thunderstorms and hurricane-season outages are a frequent reason for a wine reserve alarm. When power is lost, the cabinet slowly warms, and after power returns the display may report HI until it cools. Let it run for several hours before judging the result.

Next, check the setpoint. A set temperature changed by a cleaning wipe, a child or a bumped touch key can leave the cabinet at a different temperature from what you intended, and the display may then show HI or LO relative to the new setting. Compare the setpoint with what your guide suggests and reset it if needed.

Seasonal residents who leave a wine reserve running while away should have it checked on return, since an unnoticed outage while you are gone can leave bottles warm for days.

What can you check at a glance?

What the display shows Likely cause What you can check Next step
Door alarm, display flashing Door ajar or not sealing Clear the gasket, close firmly None if it clears
HI after an outage Cabinet warmed while off Wait several hours, use a thermometer Call if it stays
HI after loading bottles Warm load, door opened often Leave the door closed Call if it stays
LO with a changed setting Setpoint lowered by accident Reset the temperature None once set
HI or LO with no cause Sensor or cooling problem Clear vents, note the reading Technician visit
Display dark No power or control problem Confirm the breaker is on Technician visit

When should you call a technician?

Call if the display stays on HI or LO after several hours with the door closed, power on and the setpoint correct, or if the cabinet is warm to the touch while the compressor runs without cooling. Also call if the display is dark after a breaker reset.

Do not open any panel or work on the cooling system. Sealed refrigerant parts and wiring are not an owner repair. Move valuable bottles to another cool place in the meantime and keep them away from direct sun and heat.

We check the sensor, the fans, the door seal, the control board and the cooling system, and we confirm the cabinet holds its set temperature before we leave. If you are unsure about warranty effects, check your warranty terms. Independent service does not by itself void a warranty.

Frequently asked questions

How long can wine stay safe through an outage?

That depends on the room temperature and how long the cabinet was off. Measure the cabinet and the room with a thermometer rather than judging by feel, and avoid heat and direct sun for the bottles.

Can I silence the alarm?

Many controls let you silence it with a key, but the alarm returns if the cause remains. Find the cause first, then silence the alarm using the steps in your guide.

Why does the cabinet show a different temperature than my thermometer?

The control reads its own sensor, which may sit in a different spot. A small gap is common. A large gap, or one that grows, is worth a technician visit.

Should I change the temperature in summer?

Usually no. The setpoint is about what is best for the wine. If the cabinet cannot hold the setting in a hot room, improve ventilation around it and call if the problem continues.

Sources

Call Book a Repair
Call (813)750-0388 Book a Repair