(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram Dishwasher C8: Detergent Dispenser Did Not Open

C8 on a Monogram dishwasher means the control never got confirmation that the detergent dispenser door swung open on command. Gummed residue or a blocked door are simple things to rule out first.

Needs attention soonChecked November 2026

What does Monogram dishwasher code C8 mean?

C8 is a detergent dispenser problem on a Monogram dishwasher. At the point in the cycle when detergent should be released, the control board expects confirmation that the dispenser door swung open. It did not get that confirmation. Old detergent residue can gum up the mechanism, a dish or utensil can be holding the door shut, or the solenoid or actuator that pushes the door open may have failed. No series is named for this code.

C8 at a glance

Code
C8
Appliance
Monogram dishwasher
Applies to
Monogram dishwashers with a detergent dispenser
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Old detergent residue gumming the dispenser mechanism

What you may notice with C8

  • The display shows C8 during or after the wash.
  • The dispenser cup still holds detergent when the cycle ends.
  • Dishes come out spotted or dull because detergent was not released.

How the dishwasher detects C8

Partway through a wash, the control board tells the dispenser to open so detergent can drop into the water. A small solenoid or actuator releases the door, and the board expects to see that the door has actually moved. If it does not get that confirmation, it records C8.

Several things can keep the door from moving. Old detergent that has dried in the cup can glue it shut. A tall item or a misloaded rack can press against it from outside. And the solenoid or actuator itself can wear out and stop pushing. The board only knows that the release was commanded and nothing happened, so it points to the dispenser as a whole rather than to one specific cause.

Likely causes of C8

  • Old detergent residue gumming the dispenser mechanism
  • A dish, tall item or utensil physically holding the dispenser door shut
  • Dispenser solenoid or actuator that no longer releases the door

Can you keep using the dishwasher with C8?

Switch the dishwasher off at the breaker and check the dispenser before the next load. If a blockage or residue was the cause and C8 stays gone, you can keep using it. If C8 returns, the dishes will not be washed properly without detergent, so stop running cycles until the dispenser has been tested.

What you can safely check

  1. Cancel the cycle, cut power to the dishwasher at the breaker, and wait for any hot water to cool.
  2. Pull out the lower rack and look at the dispenser door for anything pressing against it.
  3. Wipe old, hardened detergent from the cup and around the door with a damp cloth.
  4. Reload so tall items or misplaced racks cannot block the door, then restore power.
  5. If C8 returns with a clean cup and clear door, leave it for a technician to test the actuator.

What our technician does for C8

  • Test whether the dispenser solenoid or actuator moves the door when commanded
  • Inspect the dispenser mechanism and latch for residue or binding
  • Replace the dispenser assembly if it fails to release

How to keep C8 from coming back

  • Wipe the dispenser cup dry after loads, so detergent cannot harden and glue the door shut.
  • Load tall items so nothing presses against the dispenser door as it swings open.
  • In hard-water parts of Tampa Bay, film can build up around the dispenser, so wipe it from time to time.

Technical reference

Code
C8
Appliance
Monogram dishwasher
Control family
Monogram dishwashers with a detergent dispenser
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

C8 questions

Can old detergent really cause C8?

Yes. Detergent that hardens in the cup can glue the door shut so it cannot swing open. Wipe the cup clean with a damp cloth when the dishwasher is off and cool.

Will the dishwasher still wash without detergent?

It will run, but the dishes will not be cleaned properly. Rerun the load once the dispenser is clear so the detergent is released at the right point in the cycle.

How do I know if a dish is blocking the dispenser?

Look at the dispenser with the power off. If a dish or handle sits against the dispenser door, it cannot swing out, so reload with space around the dispenser.

Is C8 the same as a rinse aid problem?

No. C8 refers to the detergent dispenser door not confirming that it opened. Treat it separately from rinse aid or any other additive that you use in the dishwasher.

Will C8 clear by itself after I clean the dispenser?

It can, once the door moves freely and the board confirms the release. If it returns after a clean cup and a clear door, the actuator may be failing and needs testing.

Need help with C8?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair