(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram Dishwasher: Start Status Indicator Light Flashing Explained

A blinking START status indicator on a Monogram ZDT or ZDP touch-control dishwasher tells you the door opened or the wash was cut short. No numbered error sits behind it, and pressing START resumes the wash.

Normal status, not a failureChecked November 2026

What does Monogram dishwasher code Start Status Indicator Light Flashing mean?

Touch-control Monogram ZDT and ZDP dishwashers, among them the ZDT985SPNSS and ZDT800SPFSS, show the state of a cycle through the START status indicator. A blinking indicator tells you the door was opened or the wash was interrupted. There is no numbered error attached to it. The indicator pulses on the control panel, and the dishwasher stays idle until you press START again, so there is nothing to look up in a code list.

Start Status Indicator Light Flashing at a glance

Code
Start Status Indicator Light Flashing
Appliance
Monogram dishwasher
Applies to
Monogram ZDT and ZDP touch-control dishwashers
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
The door was opened during the wash

What you may notice with Start Status Indicator Light Flashing

  • The START indicator pulses on the panel
  • The dishwasher sits quiet with dishes half washed
  • Nothing else on the panel changes or shows a number
  • The cycle does not move until you press START

How the dishwasher detects Start Status Indicator Light Flashing

The control on a ZDT or ZDP dishwasher follows the cycle step by step, and it checks the door through a latch switch the whole time. A running wash is allowed only when that switch says the door is shut. The moment the switch opens, the control stops the cycle and remembers where it was.

Because these models give owners a single light to read, the START status indicator blinks to show that the cycle is waiting. It is not reporting a broken part. It is reporting a pause. Once the door is latched and you press START within the time allowed, the control picks the wash back up from the saved step instead of beginning again.

Why Start Status Indicator Light Flashing appears

  • The door was opened during the wash
  • A power interruption or door movement stopped the cycle partway
  • The door closed without fully catching the latch
  • The door switch is sending an unsteady signal

Can you keep using the dishwasher with Start Status Indicator Light Flashing?

Yes. This is a status signal and not a hazard. Latch the door, press START, and let the cycle finish. If it blinks over and over with the door shut and nobody touching it, hold off on running full loads that you cannot babysit, because a latch or switch that drops its signal will keep pausing the wash until it is checked.

What you can safely check

  1. Wait for hot water to settle, and keep your hands away from the tub walls and heating area until everything has cooled.
  2. Push the door shut until it clicks into the latch.
  3. Touch START a single time and get the door shut inside 4 seconds.
  4. If the indicator blinks again with nobody near the door, jot down the time and cycle and call us.

What our technician does for Start Status Indicator Light Flashing

  • Test the latch and door switch with the unit open
  • Check how the door signal travels to the control if cycles stop on their own
  • Quote the repair in writing before work starts

How to keep Start Status Indicator Light Flashing from coming back

  • Make sure nothing on the lower rack sticks out and keeps the door from seating against the latch.
  • Close the door with a firm push each time instead of letting it drift shut.
  • Avoid pulling the door open mid-cycle to add a dish unless you are ready to restart.

Technical reference

Code
Start Status Indicator Light Flashing
Appliance
Monogram dishwasher
Control family
Monogram ZDT and ZDP touch-control dishwashers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

Start Status Indicator Light Flashing questions

How is the START indicator different from a code on other dishwashers?

It carries no number. It only says the wash is paused because of the door or an interruption. There is no list of codes to look up for this blink on ZDT and ZDP models.

Can I fix a blinking indicator by pressing START twice?

No. The second press cancels a running cycle. After touching START one time, you have 4 seconds to get the door closed if you want the wash to continue.

Does a blinking START light drain the tub?

No. The tub keeps its water while the cycle is paused. Only a cancel drains it, so close the door and restart if you want the cycle finished.

Will it blink forever if I leave it alone?

Yes, until the door is closed and you press START. The dishwasher keeps its place in the cycle, so waiting a while does no harm, but the dishes stay unfinished.

Is this connected to the beeping reminder on these models?

They are related but separate. Both come from an open or interrupted door, and some models add a beep every minute on top of the blinking light. Each has its own page.

Something else going on with your dishwasher?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair