Monogram Dishwasher PF: Cycle Interrupted by a Power Loss
PF on a Monogram dishwasher is a log entry showing that a power loss cut a cycle short. It is not an active mechanical problem, and the cycle should be restarted from the beginning.
What does Monogram dishwasher code PF mean?
PF is a record, not a breakdown. On a Monogram dishwasher it logs that a running cycle was interrupted when power was lost, for example during an outage or a tripped breaker. The dishwasher itself is not reporting a mechanical problem. Because the wash was stopped partway, dishes may be unclean or not rinsed, so the cycle should be run again from the start. The message is not tied to a specific series or model.
PF at a glance
- Code
- PF
- Appliance
- Monogram dishwasher
- Applies to
- Monogram dishwashers with a cycle-history message
- Type
- Normal status, not a failure
- Can you clear it yourself?
- Yes, it is a normal message or setting
- Most likely cause
- A power outage during the cycle
What you may notice with PF
- The display shows PF after power comes back.
- The dishes are wet, spotted or only partly washed.
- The cycle did not finish and the dishwasher sits idle.
How the dishwasher detects PF
A dishwasher controls the fill, wash, heat, drain and rinse steps in order, and it keeps track of where it is in the sequence. When power disappears halfway through, the control loses its place and every pump, valve and heater stops at once.
When power returns, the control sees that the last cycle never reached its end. It records PF to tell you about that, instead of treating it as a broken part. Nothing in the dishwasher has to have failed for this to happen. The wash water may have been left half-used, and the dishes may not have gone through all their rinses, so the control expects you to run the cycle again from the start.
Why PF appears
- A power outage during the cycle
- A breaker that tripped while the dishwasher was running
- The dishwasher was unplugged mid-cycle for service
Can you keep using the dishwasher with PF?
Yes, PF does not stop you from using the dishwasher. Close the door, restart the cycle from the beginning, and let it run through. Check that the dishes come out clean this time. If PF keeps returning without any outage, or the breaker trips again when the dishwasher runs, stop using it and have the supply looked at.
What you can safely check
- Make sure the dishwasher has power again, and check that the breaker has not tripped before you do anything else.
- Open the door and look inside, since dishes may still be wet or unrinsed.
- Close the door, choose your cycle, and start it again from the beginning.
- If PF disappears and the cycle completes, nothing else is needed.
- If PF keeps showing with steady power, or the breaker trips again, stop using the dishwasher and have it checked.
What our technician does for PF
- Check the power supply and wiring to the dishwasher if PF keeps appearing
- Look into why the breaker tripped if that was the cause
- Confirm the control completes a full cycle once power is steady
How to keep PF from coming back
- Avoid unplugging the dishwasher or switching it off at the breaker while it is running a cycle.
- Wait for the cycle to end before any kitchen electrical work or breaker testing.
- Expect PF after a storm outage in Florida, and simply run the cycle fresh once power is steady.
Technical reference
- Code
- PF
- Appliance
- Monogram dishwasher
- Control family
- Monogram dishwashers with a cycle-history message
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
PF questions
Is PF a sign my dishwasher is broken?
No. PF notes that power was lost during a cycle. It is a log of an interruption, so the dishwasher itself may be perfectly fine once power is steady and a new cycle completes.
Can I just finish the cycle where it stopped?
Restart it from the beginning instead. A cycle halted partway probably did not clean or rinse fully, and a fresh start gives the dishes the whole wash.
Why does PF show after I unplugged the dishwasher?
Cutting power during a running cycle counts as a power loss, so the dishwasher logs PF. It does no harm. Just start the cycle fresh when power is back.
Will PF clear by itself?
PF is a log of a past interruption, so it goes away once you start a new cycle and it completes normally. If it comes back without an outage, mention that so the power supply can be checked.
Should I worry about water left inside after PF?
Some water may remain in the tub because the cycle stopped partway. Restarting lets the dishwasher drain and finish as it normally does. If water stays after a full cycle, that needs separate attention.
Something else going on with your dishwasher?
We trace the cause in your home first and write the price down before any part is swapped.