Monogram ZBD6800 START/RESET Light Flashing After Canceling a Cycle
A flashing START/RESET light on a Monogram ZBD6800K, ZBD6880K or ZBD6890K dishwasher is not an error. It means a cycle was canceled and the tub is draining, which takes about 70 seconds.
What does Monogram dishwasher code START/RESET Light Flashing mean?
A flashing START/RESET light on the ZBD6800K, ZBD6880K and ZBD6890K Monogram top-control dishwashers is no error. Someone pressed START/RESET, so the cycle was interrupted, and the light goes out by itself once the tub has drained. After you cancel with START/RESET and shut the door, pumping out takes roughly 70 seconds, and then you can program the dishwasher again. All three models behave this way normally.
START/RESET Light Flashing at a glance
- Code
- START/RESET Light Flashing
- Appliance
- Monogram dishwasher
- Applies to
- ZBD6800K, ZBD6880K, ZBD6890K Monogram dishwashers
- Type
- Normal status, not a failure
- Can you clear it yourself?
- Yes, it is a normal message or setting
- Most likely cause
- The cycle was canceled with START/RESET, which is normal
What you may notice with START/RESET Light Flashing
- The START/RESET light flashes after you cancel a cycle
- You hear the drain pump running for a short time
- The light stops by itself once the tub is empty
- Your earlier cycle choices are gone after a power loss
How the dishwasher detects START/RESET Light Flashing
On these three models, pressing START/RESET during a running cycle tells the control to stop what it is doing. It does not simply freeze, because that would leave water sitting in the tub. Instead the control starts the drain pump and works through a pump-out routine before it accepts a new program.
While that routine runs, the START/RESET light flashes so you know the dishwasher is busy and not ready for new selections. When the water has gone, the light stops by itself and the panel is free to program again. About 70 seconds is the normal time. If power was lost, the control also forgets your earlier choices and returns to NORMAL and HEATED DRY until you pick something else.
Why START/RESET Light Flashing appears
- The cycle was canceled with START/RESET, which is normal
- The door was opened during the pump-out
- A power interruption cleared the earlier selections
- A clogged filter is slowing the drain
Can you keep using the dishwasher with START/RESET Light Flashing?
Yes. This is normal behavior and nothing needs repair. Wait for the pump-out to finish, then select your cycle and press START/RESET. If the light keeps flashing for well over two minutes and water remains in the tub, clean the filter and check the drain hose, and have the dishwasher looked at if that does not help.
What you can safely check
- Do not open the door while it drains, and let the hot water inside cool.
- Wait roughly 70 seconds for the light to stop flashing.
- Once you have chosen your cycle again, press START/RESET to begin.
- When power returns after an outage, NORMAL and HEATED DRY come back on their own, so choose what you want first.
- Clean the filter if the flashing runs on past two minutes.
What our technician does for START/RESET Light Flashing
- Test the drain pump and check the drain hose if water stays in the tub
- Look at the control if the light flashes with no button pressed
- Quote the price in writing first
How to keep START/RESET Light Flashing from coming back
- Rinse the filter regularly so the pump-out finishes in the usual time.
- Keep the door closed during the pump-out until the light stops flashing.
- After a storm or power outage, check your cycle choices before pressing START/RESET.
Technical reference
- Code
- START/RESET Light Flashing
- Appliance
- Monogram dishwasher
- Control family
- ZBD6800K, ZBD6880K, ZBD6890K Monogram dishwashers
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
START/RESET Light Flashing questions
Is a flashing START/RESET light a sign of trouble?
No, it is normal for the ZBD6800 models. The light only shows that you canceled the cycle and the pump is still emptying the tub, and it stops by itself afterward.
How long before I can start over?
Around 70 seconds with the door shut after pressing START/RESET. If the flashing continues past a couple of minutes, look at the filter and drain hose before contacting us.
Why were my choices reset after the power came back?
These models fall back on NORMAL and HEATED DRY after an outage, so choose again and press START/RESET. The control is fine when that happens.
Can I open the door while the light is flashing?
It is best not to. Opening the door during the pump-out can interrupt it. Wait until the light stops, which takes about 70 seconds, and then you can load or reprogram.
Is the flashing light the same as a drain error on these models?
No. A drain error means the water stays in the tub well past the normal time. A short flash that ends on its own is just the pump-out after a cancel.
Something else going on with your dishwasher?
We trace the cause in your home first and write the price down before any part is swapped.