(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram ZBD9900 HEAVY Light Flashing: Overfilled Tub Warning

A flashing HEAVY light on a Monogram ZBD9900 dishwasher signals an overfill. If the level does not fall within 60 seconds of pumping, the program halts.

Needs attention soonChecked November 2026

What does Monogram dishwasher code HEAVY Light Flashing mean?

ZBD9900 top-control Monogram dishwashers, among them the ZBD9900RII, use a flashing HEAVY light to report an overfill. Either the pressure sensor or the float switch told the control the tub holds too much water. When 60 seconds of pumping fails to lower the level, the program halts and the drain pump keeps running. You see the blinking light and a stopped cycle. We confirm this only for the ZBD9900 series.

HEAVY Light Flashing at a glance

Code
HEAVY Light Flashing
Appliance
Monogram dishwasher
Applies to
Monogram ZBD9900 series top-control dishwashers
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The drain pump is struggling against a blocked drain hose

What you may notice with HEAVY Light Flashing

  • The HEAVY light flashes on the panel
  • The cycle halts partway through and the dishwasher goes quiet
  • You may hear the drain pump running
  • Water stands in the tub when you open the door

How the dishwasher detects HEAVY Light Flashing

The ZBD9900 control measures how much water is in the tub with a pressure sensor, and a float switch acts as a backup. Each wash step has a water level it expects. If the sensor or the float reports more water than the step allows, the control treats it as an overfill and starts the clock.

It gives the drain pump 60 seconds to bring the level down. If the level is still too high at the end of that time, the control stops the program and keeps the pump running to empty the tub. The HEAVY light flashes to report that outcome. The control cannot say whether the water came from a slow drain, a valve that leaks through or a bad level reading, so each of those has to be checked in turn.

Likely causes of HEAVY Light Flashing

  • The drain pump is struggling against a blocked drain hose
  • The pressure sensor or float switch is giving a wrong water level
  • The inlet valve is letting water through when it should be closed
  • The flow meter or its wiring is misreporting
  • The filter and sump are clogged with debris

Can you keep using the dishwasher with HEAVY Light Flashing?

Not until it has been checked. If cleaning the filter and straightening the drain hose clears the flashing, you can carry on, but watch the next cycle. If HEAVY returns, shut the water supply valve under the sink and do not keep running it, because a valve that leaks through can keep filling the tub and water could reach the floor.

What you can safely check

  1. Cancel the cycle, unplug the dishwasher or switch off its breaker, and wait for the water to cool before touching it.
  2. Open the door with care and see whether water stands in the tub.
  3. Clean the filter and see if anything is stuck in the drain.
  4. Make sure the drain hose below the sink is not bent or pinched.
  5. Restore power and try a short cycle. If the light returns, shut the supply valve under the sink and call us.

What our technician does for HEAVY Light Flashing

  • Compare the float switch and pressure sensor readings with the actual water level
  • Tell a weak drain pump apart from an inlet valve that keeps filling
  • Check the flow meter and its wiring
  • Give a written price first

How to keep HEAVY Light Flashing from coming back

  • Rinse the bottom filter often so the sump never packs with food or glass.
  • Keep the drain hose free of kinks when the dishwasher is pushed back into place.
  • Do not stuff the lower rack so the spray arm can clear debris toward the filter.

Technical reference

Code
HEAVY Light Flashing
Appliance
Monogram dishwasher
Control family
Monogram ZBD9900 series top-control dishwashers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

HEAVY Light Flashing questions

Could the dishwasher flood the kitchen when HEAVY flashes?

The control is designed to stop the program and pump out to prevent that. If you find water on the floor anyway, close the supply valve and keep the dishwasher unplugged until we look at it.

Why did the cycle stop on its own?

When the level stays above what the program allows, and pumping cannot fix it within 60 seconds, the control ends the cycle and empties the tub. That protects the tub and your floor.

Can a dirty filter trigger the HEAVY light?

Yes, a packed filter slows the drain enough to look like an overfill. If cleaning it does not end the blinking, suspect the pump, the drain hose or the fill valve instead.

Is HEAVY the same as the code for a drain problem?

No. The drain message on this series uses two lights, AUTO and HEAVY together. HEAVY alone is the overfill message, though a slow drain can lead to either one.

What happens if I ignore it?

An inlet valve that leaks through can keep adding water, and the tub can reach a level that spills. The control tries to prevent that, but it is not meant to be relied on every cycle.

Need help with HEAVY Light Flashing?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair