Monogram ZBD9900 RINSE Light Flashing: Pressure Sensor Reading High
On a Monogram ZBD9900 dishwasher, a flashing RINSE light in the service test shows the pressure sensor signal went above 4.8 volts DC. The program continues, but fills may vary.
What does Monogram dishwasher code RINSE Light Flashing mean?
On ZBD9900 top-control Monogram dishwashers, the ZBD9900RII included, a flashing RINSE light shows a pressure sensor problem that only the technician running the service test can see. In that test the signal from the sensor went past 4.8 volts DC, beyond its normal range, while the program kept going. Owners get no message. The sensor tells the control how deep the water is in the tub, so a wrong reading may cause uneven fills. We confirm this reading for the ZBD9900 series only.
RINSE Light Flashing at a glance
- Code
- RINSE Light Flashing
- Appliance
- Monogram dishwasher
- Applies to
- Monogram ZBD9900 series top-control dishwashers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- The pressure sensor or its hose is clogged or damaged
What you may notice with RINSE Light Flashing
- Nothing appears on the panel during normal use
- Water levels in the tub look different from load to load
- Wash results vary without a clear reason
- The tub may look low on water at a fill step
How the dishwasher detects RINSE Light Flashing
The pressure sensor in a ZBD9900 reads the weight of the water in the tub through a small hose and turns it into a voltage. The control watches that voltage to know how deep the water is, and it uses the answer to decide when to stop filling, when to start the pump and whether a step is complete.
The voltage normally stays below 4.8 volts DC. If the signal rises above that value, the control decides the sensor reading is outside its useful range and flags it. It does not stop the cycle, since it can still follow timing. The flashing RINSE light is stored for the service test. With a doubtful level reading, the control may fill a little too much or too little, which is why wash results can vary.
Likely causes of RINSE Light Flashing
- The pressure sensor or its hose is clogged or damaged
- The wiring to the pressure sensor is loose or damaged
- The main control input for the sensor is misreading
Can you keep using the dishwasher with RINSE Light Flashing?
Yes, you can keep using it, because the program continues. Watch the water level in the tub. If it looks very high or very low, or if water ever seems to rise toward the door, stop and close the supply valve. Otherwise it is safe to run while you wait for the sensor to be tested.
What you can safely check
- Let the cycle finish, then switch off power at the breaker or unplug the dishwasher before reaching in.
- Note how much water is left in the tub afterward.
- Clean the filter and the sump area.
- Make sure nothing plugs the drain at the tub floor.
- Restore power, run another cycle and watch the fill. If the water looks too low or too high, call us.
What our technician does for RINSE Light Flashing
- Read the RINSE flash in the service test
- Look for clogs in the sensor hose and damage on its wiring
- Compare the sensor reading with the real water level
- Quote in writing before any part is ordered
How to keep RINSE Light Flashing from coming back
- Rinse the bottom filter and sump area often so debris does not reach the sensor hose.
- Keep the drain clear so water levels fall the way the control expects.
- Scrape plates before loading to keep food from collecting in the tub base.
Technical reference
- Code
- RINSE Light Flashing
- Appliance
- Monogram dishwasher
- Control family
- Monogram ZBD9900 series top-control dishwashers
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
RINSE Light Flashing questions
Will it still wash?
Yes, the program goes on. If the sensor reading is off, though, the fill amount may be wrong, so results can differ from one load to the next.
How is this different from an overfill?
The HEAVY light is the overfill message that owners can see. RINSE concerns the sensor signal itself and appears only in the service test.
Does the sensor itself need replacing?
Not always. A clogged sensor hose or a loose connector can give the same reading, so we test those before suggesting a part, and sometimes the fix is simple.
How is RINSE different from the other flashing lights on this series?
Each light names a different condition. RINSE points to the pressure sensor signal, while HEAVY reports an overfill and AUTO reports slow heating. They are separate readings.
Will the reading clear by itself?
Only if the cause was a temporary blockage that went away. A sensor, hose or connector that is damaged will keep sending the same signal until it is repaired.
Need help with RINSE Light Flashing?
We trace the cause in your home first and write the price down before any part is swapped.