Monogram ZBD9900 AUTO + HEAVY Lights Flashing: Water Not Draining
A pair of flashing AUTO and HEAVY lights on a Monogram ZBD9900 dishwasher is a drain message. The water was still in the tub after 120 seconds of pumping, so the program stopped.
What does Monogram dishwasher code AUTO + HEAVY Lights Flashing mean?
The ZBD9900 top-control Monogram dishwasher, the ZBD9900RII for one, uses AUTO and HEAVY flashing together to report a drain problem. After 120 seconds the water had not been pumped out, so the program stopped. You see both lights flashing, with water left standing in the tub. A dirty filter may be all that is wrong. We confirm this meaning only for the ZBD9900 series.
AUTO + HEAVY Lights Flashing at a glance
- Code
- AUTO + HEAVY Lights Flashing
- Appliance
- Monogram dishwasher
- Applies to
- Monogram ZBD9900 series top-control dishwashers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- The filter or sump is clogged with debris
What you may notice with AUTO + HEAVY Lights Flashing
- The AUTO and HEAVY lights flash together
- The cycle stops with water left in the tub
- The drain pump may hum or stay quiet
- Standing water smells of old food
How the dishwasher detects AUTO + HEAVY Lights Flashing
At the end of a wash step, the ZBD9900 control starts the drain pump and expects the tub to empty. It judges the result from the pressure sensor, which tells it how much water is left. A tub that empties as expected lets the cycle move on to the next step.
If the water is still there after 120 seconds, the control concludes that the drain has failed. It stops the program and flashes the AUTO and HEAVY lights together so that the drain message can be told apart from the single HEAVY overfill message. The control cannot see why the water stayed. A clogged filter, a weak pump, a pinched hose or a blocked disposer connection all leave the same result.
Likely causes of AUTO + HEAVY Lights Flashing
- The filter or sump is clogged with debris
- The drain pump is not moving the water
- The drain hose is blocked or kinked
- The drain connection at the sink or disposer is restricted
- The control output to the drain pump is not working
Can you keep using the dishwasher with AUTO + HEAVY Lights Flashing?
Not until the water drains. Standing water can smell and carry food into the tub, and the dishwasher will not finish a cycle. Cleaning the filter often solves it, and if so you can carry on. If the water stays after cleaning and a hose check, stop using it and have the pump and hose tested.
What you can safely check
- Stop the cycle, unplug the dishwasher or switch off its breaker, and wait for the standing water to cool.
- Open the door carefully and see how much water is in the tub.
- Lift out the filter at the bottom and clean it.
- Look for food or broken glass in the sump area.
- Look along the drain hose beneath the sink for a sharp bend.
- Restore power and run a short cycle. If the lights flash again, call us.
What our technician does for AUTO + HEAVY Lights Flashing
- Test the drain pump and the control output to it
- Check the drain hose and the air gap
- Look at the disposer knockout plug if a disposer is connected
How to keep AUTO + HEAVY Lights Flashing from coming back
- Rinse the bottom filter regularly and check the sump for glass or bones.
- Keep the drain hose straight where it runs under the sink.
- Scrape large food scraps into the trash before loading, rather than letting them reach the sump.
Technical reference
- Code
- AUTO + HEAVY Lights Flashing
- Appliance
- Monogram dishwasher
- Control family
- Monogram ZBD9900 series top-control dishwashers
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
AUTO + HEAVY Lights Flashing questions
Why do two lights flash together?
This series uses the pairing for its drain message, since either light alone means something different. The combination tells us where to look first.
May I remove the standing water myself?
You may scoop it out with a cup and rinse the filter afterward. Never tilt or slide the dishwasher, and leave it unplugged if water spilled.
Is cleaning the filter enough?
Frequently, because debris slows the drain. If water remains afterward, we move on to the pump and the drain hose.
Is this different from the HEAVY light alone?
Yes. HEAVY alone reports an overfill, while the AUTO and HEAVY pair reports that the water would not drain. A slow drain can sometimes lead to either, so we check both.
Will it keep returning if I only clean the filter?
It can. If the cause is a weak pump or a blocked hose, a clean filter helps only briefly, and the lights will come back until the real problem is repaired.
Need help with AUTO + HEAVY Lights Flashing?
We trace the cause in your home first and write the price down before any part is swapped.