Monogram Dishwasher C5: Incomplete or Restricted Draining
C5 on a Monogram dishwasher means water is not leaving the tub properly during the drain phase. Unlike C2, it flags incomplete or restricted draining rather than slow draining.
What does Monogram dishwasher code C5 mean?
C5 means a Monogram dishwasher is not draining properly during its drain phase. This differs from C2, which is about a drain that takes too long. C5 says drainage is incomplete or restricted, so water is left behind rather than just leaving slowly. The simplest cause an owner can reach is a drain filter or screen clogged with food debris. A blocked drain hose or air gap, or a drain pump that is failing, are the other causes.
C5 at a glance
- Code
- C5
- Appliance
- Monogram dishwasher
- Applies to
- Monogram dishwashers with a drain filter and pump
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Drain filter or screen packed with food debris
What you may notice with C5
- The display shows C5 and water stays in the bottom of the tub.
- Dishes come out wet, gritty or with a dirty film.
- The dishwasher may hum or run without emptying.
How the dishwasher detects C5
During the drain phase, the dishwasher's pump pushes dirty water out through the drain hose and into the home's drain line, sometimes through an air gap fitting at the sink. The control expects the tub to empty fully before the next fill or the end of the cycle. When water is still there, it shows C5.
Where the water gets stuck can be anywhere along that path. A filter or screen at the bottom of the tub clogs with food debris and holds water back. A hose that is blocked, or an air gap fitting at the sink, can restrict the flow. And a drain pump that is failing can spin without moving enough water. C5 reports the result, incomplete or restricted draining, and not the single place where it happens.
Likely causes of C5
- Drain filter or screen packed with food debris
- Drain hose or air gap blocked
- Drain pump weakening and moving too little water
Can you keep using the dishwasher with C5?
Do not keep running cycles with C5 showing. Water that will not drain can spill past the door or back up from the drain line, and dishes will not be cleaned in dirty water. After you rinse the filter and check the hose, one test cycle is reasonable. If water stays again, stop and switch the dishwasher off at the breaker until the pump is tested.
What you can safely check
- Pause the cycle, shut the dishwasher's breaker off, and let any hot water cool before reaching in.
- Remove the lower rack and lift out the drain filter or screen at the bottom of the tub.
- Rinse off food debris and put the filter back fully seated.
- Check the drain hose behind the dishwasher for a kink or crush where you can see it, without pulling the unit out.
- If water still stays after a clean filter and clear hose, stop using it so the drain pump can be tested.
What our technician does for C5
- Check that the drain hose and air gap pass water freely
- Test the drain pump for power and flow
- Replace the drain pump if it fails to move water out
How to keep C5 from coming back
- Scrape plates before loading and rinse the drain filter when you see debris collecting.
- Keep the drain hose behind the dishwasher free of kinks, and do not crush it when sliding the unit back.
- Clear the air gap at the sink from time to time if your kitchen has one.
Technical reference
- Code
- C5
- Appliance
- Monogram dishwasher
- Control family
- Monogram dishwashers with a drain filter and pump
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
C5 questions
What is the difference between C5 and C2?
C2 flags a drain that takes too long. C5 flags drainage that is incomplete or restricted, so some water is left behind. The checks overlap, but the codes describe different problems.
Is standing water in the tub a problem?
Yes. Water left in the tub can smell and, if the cause is a clogged hose, back up. Leave the cycle off and clear what you can reach.
How often should I clean the drain filter?
Rinse it whenever you see food collecting, and check it if the dishwasher starts to leave water or dirt behind. A clean filter keeps the pump working freely.
Will C5 clear by itself once the filter is clean?
It can, when the filter was the only blockage and water now leaves fully during the next drain phase. If C5 returns, the hose, air gap or pump is the next place to look.
What should I mention about C5 before the visit?
Say whether water is left standing, when you last cleaned the filter, and whether the sink has an air gap. That points us toward the hose or the pump first.
Need help with C5?
We trace the cause in your home first and write the price down before any part is swapped.