(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram Dishwasher C3: Fill Taking Too Long to Reach Level

C3 on a Monogram dishwasher means water did not reach the expected level within the normal fill time. A partly closed supply valve is a simple cause to check first.

Needs attention soonChecked November 2026

What does Monogram dishwasher code C3 mean?

C3 is a long-fill problem on a Monogram dishwasher. During the fill step, the unit expects water to reach the right level within its normal fill time, and it did not. The supply valve under the sink may be only partly open, a kink in the supply line may be restricting flow, or the water inlet valve inside the dishwasher may have failed. No series is named for this code.

C3 at a glance

Code
C3
Appliance
Monogram dishwasher
Applies to
Monogram dishwashers with a water inlet valve
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Supply valve under the sink opened only part way

What you may notice with C3

  • The display shows C3 and the cycle stalls near the start.
  • You hear the dishwasher fill slowly, or very little water enters.
  • The tub holds less water than usual when you open it.

How the dishwasher detects C3

In the fill step, the control opens the water inlet valve and waits for water to rise to the proper level in the tub. It expects that to happen within a normal period of time, since the flow from a fully open supply is fairly steady. If the level is still short when that time is up, it displays C3.

The supply path has three places where flow can be held back. The shut-off valve under the sink may be turned only partway. The supply line may be kinked, which narrows the passage. Or the inlet valve inside the dishwasher may no longer open fully, so only a trickle gets through. The control cannot see which one it is, only that the tub filled too slowly, so the simple checks come first.

Likely causes of C3

  • Supply valve under the sink opened only part way
  • Supply line bent or kinked along its run
  • Water inlet valve no longer opening fully

Can you keep using the dishwasher with C3?

You can try the dishwasher again once the shut-off valve is turned all the way open and the line has no bends. If it fills normally, carry on. If C3 returns, stop running cycles, because washing with too little water leaves dishes dirty. Switch it off at the breaker until the inlet valve has been tested.

What you can safely check

  1. Stop the cycle and switch the dishwasher off at the breaker before reaching under the sink.
  2. Make sure the shut-off valve beneath the sink is turned all the way open.
  3. Look at the supply line you can see for a kink, bend or crushed spot, and straighten it gently.
  4. Restore power and start a new cycle, watching whether water enters.
  5. If C3 returns with the valve fully open and the line clear, stop using it so the inlet valve can be tested.

What our technician does for C3

  • Check water flow reaching the inlet valve
  • Test the water inlet valve for power and a full opening
  • Replace the inlet valve if it does not pass water properly

How to keep C3 from coming back

  • Open the supply valve fully after any plumbing work under the sink, and check it is not left partly closed.
  • Keep the supply line free of sharp bends when the dishwasher is pushed back into place.
  • In Tampa Bay homes on hard or well water, scale can narrow valve openings, so mention slow fills early.

Technical reference

Code
C3
Appliance
Monogram dishwasher
Control family
Monogram dishwashers with a water inlet valve
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

C3 questions

Why would a half-open valve cause C3?

The dishwasher expects the tub to fill within a set time. A valve that is only partly open delivers less water each minute, so the tub does not reach its level in time.

Can weak water flow at home cause C3?

Weak flow into the dishwasher has the same effect, so check the supply valve and line first. If the rest of the house runs normally, the problem is nearer the dishwasher.

Is it safe to leave the supply valve open?

Yes, for normal use. If you leave home for a while, or you ever see water around the dishwasher, close it.

Is C3 related to a leak?

No. C3 is about too little water arriving during the fill, not water escaping. A drip under the sink is a separate matter, and it deserves its own look.

Will C3 clear by itself after I open the valve?

It can, once the tub reaches its level on time. If it comes back with a fully open valve and a straight line, the inlet valve inside the dishwasher needs testing.

Need help with C3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair