(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram Dishwasher Code C9: Base Pan Leak Alert Explained

C9 on a Monogram dishwasher is a leak alert for water pooling in the base pan. It is related to C1 but reaches the control through a different sensor path on some platforms.

Needs attention soonChecked November 2026

What does Monogram dishwasher code C9 mean?

C9 is a leak-detected alert linked to water collecting in the base pan beneath the dishwasher tub. It is closely related to C1, though on some control platforms it arrives through a different sensor path. Possible sources are a door gasket that has failed, a hose fitting that is cracked or loose, or a cracked tub or sump part. Treat it as real water until proven otherwise, because the pan sits where owners cannot see it.

C9 at a glance

Code
C9
Appliance
Monogram dishwasher
Applies to
Monogram dishwashers with base pan leak detection
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Door gasket no longer sealing along the tub opening

What you may notice with C9

  • The display shows C9 and the cycle stops.
  • Water may be visible on the floor in front of the dishwasher.
  • The dishwasher may sound or look normal while the pan holds water.

How the dishwasher detects C9

Under the tub of a dishwasher is a shallow base pan whose job is to catch stray water. A sensor in or near that pan notices water and reports it to the control board, which stops the cycle so the leak does not spread to the floor and cabinet.

C9 reports this condition by a sensor path that differs from the one behind C1 on some control platforms. Either way the logic is the same: water was found where it should not be. The water can come from the door seal, from a hose fitting that has cracked or loosened, or from the tub or sump part itself. The board cannot tell which, so it simply protects the kitchen and displays the code.

Likely causes of C9

  • Door gasket no longer sealing along the tub opening
  • Hose fitting that has cracked or worked loose
  • Cracked tub or sump part letting water into the base

Can you keep using the dishwasher with C9?

Do not keep running the dishwasher with C9 showing. Turn off the water supply to it first, and do not start another cycle until a technician has confirmed there is no active leak. Water in the base pan can reach the floor and cabinet, and electrical parts sit close by. Wipe up spills and keep the door closed until it has been checked.

What you can safely check

  1. Stop the cycle, turn off the water supply valve to the dishwasher, and switch the dishwasher off at its breaker.
  2. Look at the floor and the cabinet front for water, and wipe up anything you find.
  3. Check the door gasket for visible tears or a gap, without pulling anything apart.
  4. Hold off on any new cycle until a technician has confirmed there is no active leak.
  5. Note whether C9 appeared mid-cycle or right after the fill, and pass that on.

What our technician does for C9

  • Pull the dishwasher from its cabinet opening to reach the base pan
  • Run the unit under observation to find which part is leaking
  • Replace the gasket, hose fitting or cracked tub or sump part

How to keep C9 from coming back

  • Check the door gasket from time to time for tears or food stuck in the seal.
  • Do not overload or force the racks, so the door can close fully against the gasket.
  • Watch for damp spots under the sink or on the cabinet floor and mention them early.

Technical reference

Code
C9
Appliance
Monogram dishwasher
Control family
Monogram dishwashers with base pan leak detection
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

C9 questions

Is C9 the same as C1?

They are closely related leak alerts. On some control platforms C9 is reported by another sensor route, so the leak is checked the same way whichever code shows.

Can I wipe the pan dry myself?

The base pan sits under the tub and cannot be reached without removing the unit from its cabinet opening, so it is not an owner job. Dry what you can see on the floor and leave the rest to a technician.

Why did C9 appear if I see no water?

The pan is hidden under the tub, so a leak can collect there before any puddle reaches the floor. The alert is meant to catch the water early.

Will C9 clear by itself after the water dries?

Do not count on it. The alert tells you water was found in the base pan, and the source of that water is still there until it is repaired. Wait for a technician to confirm there is no active leak.

What should I say about C9 on the phone?

Tell us when the code appeared, whether you saw water on the floor, and whether the supply valve is now off. That helps us bring the right parts for the gasket, hose or tub.

Need help with C9?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair