Monogram Dishwasher C1: Leak Detected in the Base Pan
C1 on a Monogram dishwasher means leak detection found water collecting in the pan beneath the tub and stopped the cycle. Turn off the water supply and leave the dishwasher unused until it is checked.
What does Monogram dishwasher code C1 mean?
C1 means the leak-detection system on a Monogram dishwasher found water in the base pan beneath the tub, where water does not belong. The dishwasher stopped the cycle so the water would not reach your floor. A door gasket that has failed and lets water past the seal is one possible source. A hose fitting that is cracked or loose and an inlet valve that has failed are others. No series is named for this code.
C1 at a glance
- Code
- C1
- Appliance
- Monogram dishwasher
- Applies to
- Monogram dishwashers with leak detection
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Door gasket allowing water to escape past the seal
What you may notice with C1
- The display shows C1 and the cycle stops.
- Water may appear on the floor or at the door edge.
- A damp cabinet floor or a musty smell can be a sign.
How the dishwasher detects C1
Under the tub, a dishwasher has a shallow base pan that collects any water that escapes from the tub, hoses or valves. A leak-detection system watches the pan, and when it finds water there it stops the cycle at once so the water does not reach your floor or cabinets. That is why C1 appears even before you see a puddle.
The water can come from several places. The door gasket can fail to seal and let water past the door edge. A hose fitting under the tub can crack or loosen. The water inlet valve can fail and let water in when it should be closed. The sensor reports only that water is in the pan. Finding which part is responsible takes the unit pulled from its cabinet opening and run under observation.
Likely causes of C1
- Door gasket allowing water to escape past the seal
- Hose fitting cracked or loosened under the tub
- Failed water inlet valve letting water into the base
Can you keep using the dishwasher with C1?
Do not use the dishwasher while C1 is showing. Close the water supply to it, switch it off at the breaker, and leave it unused until a technician confirms there is no active leak. Water in the base pan can reach the floor and cabinet, and it can spread under nearby flooring where you cannot see it.
What you can safely check
- Stop the cycle, close the water supply valve to the dishwasher, and switch the dishwasher off at its breaker.
- Check the floor and cabinet around it, and wipe up standing water.
- Look at the door gasket for tears or gaps you can see without pulling anything apart.
- Do not run another cycle until a technician has confirmed there is no active leak.
- Make a note of what you saw, such as where water showed up, to pass on.
What our technician does for C1
- Remove the dishwasher from its cabinet opening to reach the base pan
- Run the dishwasher under observation to see which part is leaking
- Replace the door gasket, hose fitting or water inlet valve that is leaking
How to keep C1 from coming back
- Check the door gasket now and then for tears, gaps or food caught in the seal.
- Mention drips under the sink or damp spots in the cabinet early.
- In humid Florida kitchens, a damp cabinet floor can be mistaken for condensation, so look for the actual source.
Technical reference
- Code
- C1
- Appliance
- Monogram dishwasher
- Control family
- Monogram dishwashers with leak detection
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram dishwasher error codes
C1 questions
Is C1 serious if I see no puddle?
Treat it seriously. The pan sits under the tub, so water can collect there before any reaches the floor. The leak sensor caught it early, which is its job.
Can I keep using the dishwasher if I dry the pan?
No. The pan cannot be reached unless the dishwasher is pulled out of its cabinet space, and the source is still active. Stop running cycles and leave the supply off.
How is the leaking part found?
The technician pulls the dishwasher out and runs it while watching for water, because the exact source can only be seen with the unit running.
Will C1 clear by itself once the pan dries?
Do not rely on that. A dry pan does not mean the leaking part is repaired, so the alert may return the next time the dishwasher runs.
What details about C1 help the technician?
Say when the code showed, where you saw water, and whether the supply valve is closed now. That lets us bring the right gasket, hose fitting or inlet valve.
Need help with C1?
We trace the cause in your home first and write the price down before any part is swapped.