(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram Dishwasher LEAK DETECTED Message: Stop and Find the Water

LEAK DETECTED on a Monogram ZDT or ZDP dishwasher means the sensor found water in the wrong spot. The machine pumps out and cancels the wash to protect your floor and cabinet.

Stop using it until checkedChecked November 2026

What does Monogram dishwasher code LEAK DETECTED mean?

Leak detection is built into some Monogram ZDT and ZDP dishwashers, including the ZDT985SPNSS and the ZDT800SPFSS, which have touch controls. Should the sensor find stray water, the dishwasher empties itself, ends the wash early and displays LEAK DETECTED. Expect to see that message, a stopped wash, and perhaps a puddle on the floor or inside the base. It is a protective stop, never a regular finish.

LEAK DETECTED at a glance

Code
LEAK DETECTED
Appliance
Monogram dishwasher
Applies to
Monogram ZDT and ZDP touch-control dishwashers with leak detection
Type
Stop using it until checked
Can you clear it yourself?
No, stop using it until it is checked
Most likely cause
Water has gathered in the base underneath the tub

What you may notice with LEAK DETECTED

  • LEAK DETECTED appears on the display
  • The wash stops partway through and the tub drains
  • Water may sit on the kitchen floor near the unit
  • The area under or beside the door looks wet

How the dishwasher detects LEAK DETECTED

Models with leak detection carry a sensor low in the base of the dishwasher, where water would collect if something inside the tub or the plumbing started to drip. The control keeps reading that sensor while the wash runs. Dry means normal. Wet tells the control that water has gone somewhere it was never meant to go.

When the sensor reads wet, the dishwasher does not try to finish the cycle. It runs the drain pump to empty the tub, cancels the wash, and puts LEAK DETECTED on the display. The goal is to stop adding water to a path that is already leaking. The message names the sensor condition only, and it cannot say where the water came from.

Likely causes of LEAK DETECTED

  • Water has gathered in the base underneath the tub
  • The door seal or door edge is letting water out
  • A fill or drain connection is weeping under the dishwasher
  • The leak sensor still reads wet after an old spill

Can you keep using the dishwasher with LEAK DETECTED?

No. Do not run the dishwasher again until the water source has been found. Running another wash over a true leak can soak the cabinet and damage flooring, and water near an outlet adds an electrical hazard. Unplug it or switch off its breaker if water is spreading, wipe up the floor, and shut the supply valve under the sink if you can reach it without standing in water.

What you can safely check

  1. Cancel anything running, unplug the dishwasher or switch off its breaker, and let hot water inside cool.
  2. Mop up water on the floor so nobody slips.
  3. Open the sink cabinet and look for damp spots where the supply and drain lines connect.
  4. Leave the dishwasher unused. Call us with the model number, and mention whether water keeps showing up with the machine off.

What our technician does for LEAK DETECTED

  • Trace the water back to the door seal, spray arms, hoses or tub base
  • Check whether the leak sensor is wet from a past spill or an active leak
  • Repair or replace the leaking part and confirm the sensor reads dry
  • Give you a written price before any work

How to keep LEAK DETECTED from coming back

  • Wipe spills and drips off the door edge and tub rim so the sensor is not tripped by old moisture.
  • Glance under the sink now and then for damp supply or drain connections.
  • Do not overload the lower rack so spray arms can turn freely and throw water only inside the tub.

Technical reference

Code
LEAK DETECTED
Appliance
Monogram dishwasher
Control family
Monogram ZDT and ZDP touch-control dishwashers with leak detection
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

LEAK DETECTED questions

Does LEAK DETECTED always mean water is on the floor?

Not always. The sensor sits in the base, so it can trip on water that has not reached the floor yet. Still, treat it as real until someone has looked under and behind the dishwasher.

Is it safe to wipe the base dry and try again?

We would not. Wiping may remove the sign without removing the cause, and a second cycle could push more water into the cabinet. Let us find the source first.

Do all Monogram dishwashers have this sensor?

No. Only some ZDT and ZDP models include leak detection, so check the model number on the door edge or call us with it and we will confirm.

Could the message appear after a spill that is already cleaned up?

Yes, it can. A sensor that stays wet after a past spill looks just like an active leak until the base is inspected and dried. That is why we check before calling it a false alarm.

What should I tell you on the phone?

Tell us the model number, whether water was on the floor, and whether it keeps appearing with the dishwasher switched off. Those details help us decide whether the door seal, a hose or the base is the likely place.

Need help with LEAK DETECTED?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair