(813)750-0388 Book a Repair
Monogram dishwasher error code

Monogram ZBD9900 AUTO + SPEED Lights Flashing: Turbidity Sensor

When AUTO and SPEED flash together on a Monogram ZBD9900 dishwasher, the service test reports the turbidity sensor as uncertain. The Auto program then assumes the water is very dirty.

Needs attention soonChecked November 2026

What does Monogram dishwasher code AUTO + SPEED Lights Flashing mean?

When AUTO and SPEED flash together on a ZBD9900 top-control Monogram dishwasher, the ZBD9900RII for example, the technician's service test is pointing at the turbidity sensor. If the control cannot tell what that sensor is reading, the Auto program assumes very dirty water. Owners see no message, just an Auto cycle that can take longer or draw extra water. We confirm this for the ZBD9900 series only.

AUTO + SPEED Lights Flashing at a glance

Code
AUTO + SPEED Lights Flashing
Appliance
Monogram dishwasher
Applies to
Monogram ZBD9900 series top-control dishwashers
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The turbidity sensor lens is covered with film

What you may notice with AUTO + SPEED Lights Flashing

  • Nothing appears on the panel during an Auto cycle
  • The Auto cycle runs longer than you expect
  • Water use looks higher than usual
  • A film coats the tub walls near the sump

How the dishwasher detects AUTO + SPEED Lights Flashing

The Auto program on a ZBD9900 does not run on a fixed clock. It uses a turbidity sensor that looks through the wash water and judges how cloudy it is. Cloudy water means a dirty load, and the control then adds rinse time or water. Clear water means the load is clean and the cycle can finish sooner.

When the sensor gives an answer the control cannot trust, it plays safe. It assumes the water is very dirty and runs the Auto program as if the load were heavy. The AUTO and SPEED lights flash together in the service test to record that the sensor was uncertain. A film on the sensor lens, debris in the water path or loose wiring can each cause an uncertain reading, which is why cleaning is worth trying first.

Likely causes of AUTO + SPEED Lights Flashing

  • The turbidity sensor lens is covered with film
  • The filters and sump hold debris
  • The drain system is slow to clear water
  • The wiring between the sensor and the control is loose

Can you keep using the dishwasher with AUTO + SPEED Lights Flashing?

Yes, you can keep using it, and the dishes will still be cleaned. The Auto program just plays safe, so it may run longer and use more water. If you want shorter cycles in the meantime, choose another program that runs on fixed timing. If the Auto cycle stays long after cleaning the filter, have the sensor checked.

What you can safely check

  1. Let the cycle end, then switch off power at the breaker or unplug the dishwasher before reaching in.
  2. Pull out the bottom filter and rinse any film from it.
  3. Wipe film or residue off the tub walls and around the sump.
  4. Confirm that the drain is clear and the hose has no sharp bend.
  5. Restore power, run an Auto cycle with an ordinary load and time it. If it keeps running long, call us.

What our technician does for AUTO + SPEED Lights Flashing

  • Examine the sensor, its wiring and how quickly water drains
  • Tell a dirty lens apart from a sensor that has stopped working
  • Provide a written price before any part is ordered

How to keep AUTO + SPEED Lights Flashing from coming back

  • Rinse the bottom filter every week or so to keep film off the sensor path.
  • Wipe film from the tub walls and sump area before it hardens.
  • If your water is hard, mention it to us so we can look at the sensor for film buildup.

Technical reference

Code
AUTO + SPEED Lights Flashing
Appliance
Monogram dishwasher
Control family
Monogram ZBD9900 series top-control dishwashers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

AUTO + SPEED Lights Flashing questions

Does it still clean?

Yes. When unsure, Auto assumes dirty water and runs long and thorough, so expect extra water and longer cycles.

Why does only Auto behave differently?

Only Auto depends on the turbidity sensor to judge how dirty the water is, while other programs run on fixed times.

Could the water itself be the cause?

Film from hard water or leftover food can cloud the sensor lens. We check the water and filters before the circuit, and that tells us whether cleaning or a part is needed.

Is this the same as the AUTO light flashing alone?

No. AUTO alone reports water that heated too slowly, while AUTO and SPEED together point to the turbidity sensor. Each one is a separate reading on the same series.

Will the sensor reading fix itself?

If a film was the cause, cleaning may bring it back. A sensor or wire that has stopped working keeps returning the same reading until it is tested.

Need help with AUTO + SPEED Lights Flashing?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair