(813)750-0388 Book a Repair
Monogram wall oven error code

Monogram ZET Wall Oven F3: Open Oven Temperature Sensor

A Monogram ZET wall oven stores F3 when the control reads the oven sensor as open, above 2,900 ohms. Because the code is hidden, you notice poor or missing heat instead.

Needs attention soonChecked November 2026

What does Monogram wall oven code F3 mean?

In Monogram 30-inch convection wall ovens from the ZET1 and ZET2 series, whether single or double, including the ZET1PL1SS and ZET2SL1SS, an open oven sensor, meaning a reading above 2,900 ohms, makes the control store F3. At room temperature a sound sensor measures near 1,080 ohms, and its resistance moves about 2 ohms for each degree. F3 stays in the stored codes and never appears on the display, so the signs you notice are an oven that heats poorly, heats unevenly, or quits partway through a bake.

F3 at a glance

Code
F3
Appliance
Monogram wall oven
Applies to
Monogram ZET1 and ZET2 wall ovens, oven sensor circuit
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Sensor element that has gone open

What you may notice with F3

  • The oven heats poorly or not at all
  • A bake ends early or stops partway through
  • Heating seems uneven, and no code shows on the display

How the wall oven detects F3

The oven sensor is a temperature-sensitive resistor. Its resistance changes with heat, so the control reads the number of ohms and converts it to a cavity temperature, starting from about 1,080 ohms at room temperature.

If the circuit is broken, the reading jumps beyond 2,900 ohms, far above the healthy value, and the control stores F3 for an open sensor. The break may be inside the sensor, in a lead, or at a connector. Because the owner display never shows F3, the oven can heat badly, heat unevenly or stop partway through a cycle without any message, and that explains why the stored history matters when a technician looks at the oven.

Likely causes of F3

  • Sensor element that has gone open
  • Sensor connector loose or corroded
  • Broken wire in the sensor lead
  • Relay board or control input misreading the sensor

Can you keep using the wall oven with F3?

F3 is not shown on the display, so judge the oven by how it behaves. If it still heats and holds temperature, you can keep using it while you watch it, but do not leave it unattended. If it will not heat, or it stops partway through, switch it off and leave it. The sensor is what tells the control how hot the cavity is.

What you can safely check

  1. Turn the oven off at its controls and let it cool completely.
  2. Look for racks or foil leaning on the back wall of the oven.
  3. Run a brief bake at a moderate setting and see whether the oven heats.
  4. If it will not heat, contact us and say what you noticed.

What our technician does for F3

  • Measure the sensor's resistance against the open reading
  • Test the sensor leads and connector
  • Read the stored code history
  • Check the relay board input if the sensor tests good

How to keep F3 from coming back

  • Keep foil and pans from touching the rear wall of the cavity where the sensor leads run.
  • In humid Florida kitchens, ventilate the room so moisture does not sit on oven connections.

Technical reference

Code
F3
Appliance
Monogram wall oven
Control family
Monogram ZET1 and ZET2 wall ovens, oven sensor circuit
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

F3 questions

Why doesn't my oven display F3?

The code is stored in the control and hidden from the owner. What you see instead is poor heating or an oven that stops partway through cooking.

What does 2,900 ohms signify?

It is the line the control uses for an open sensor. A sensor above 2,900 ohms is treated as open, compared with about 1,080 ohms for a healthy one at room temperature.

Can a loose connector cause F3?

Yes. A loose or corroded connector can look exactly like a dead sensor, so the sensor and its leads are both measured before a new sensor is chosen.

How is F3 different from a shorted sensor code?

F3 means the resistance is above 2,900 ohms, an open circuit, while a shorted sensor reads far below the healthy value. They point to opposite problems in one circuit.

Will a new sensor always fix it?

Not always. The leads, connectors and the relay board input can produce the same reading, which is why they are tested before a part is chosen.

Need help with F3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair