(813)750-0388 Book a Repair
Monogram wall oven error code

Monogram ZET Wall Oven F2: Cavity Temperature Too High

F2 on a Monogram ZET wall oven means the cavity sensor read a temperature above the limit, so the oven shut its heating down. Let it cool completely before you try again.

Stop using it until checkedChecked November 2026

What does Monogram wall oven code F2 mean?

F2 is logged by Monogram ZET1 and ZET2 wall ovens, the 30-inch convection models in single or double form, such as the ZET1PL1SS and ZET2SL1SS, when the cavity sensor reads too hot. Ordinary cooking has a ceiling of 650 degrees F at the cavity sensor, and a latched self-clean has a higher ceiling of 915 degrees F. When either is passed, the oven cuts its heating and F2 appears on the display. The sources named in the documentation are relay contacts welded shut on the relay board, limited airflow behind the oven, and extra resistance in the sensor leads or their connectors.

F2 at a glance

Code
F2
Appliance
Monogram wall oven
Applies to
Monogram ZET1 and ZET2 convection wall ovens (30-inch)
Type
Stop using it until checked
Can you clear it yourself?
No, stop using it until it is checked
Most likely cause
Relay contacts welded closed on the relay board

What you may notice with F2

  • F2 appears on the oven display
  • The oven stops heating by itself
  • The cavity can feel very hot after the shutdown
  • The oven may have just finished a long, very hot cycle

How the wall oven detects F2

A temperature sensor inside the oven cavity reports the heat to the control, and the control compares it with two ceilings. One applies to ordinary cooking, 650 degrees F. The other applies to a latched self-clean, 915 degrees F.

F2 is logged when the reading goes beyond the ceiling that fits the mode, and the control cuts the heating. A relay on the relay board that has stuck closed can keep power flowing, restricted airflow behind the oven can trap heat, and a sensor lead with too much resistance can feed the control a wrong number. Three separate causes produce the same code, which is why the technician works through them one at a time instead of replacing a part right away.

Likely causes of F2

  • Relay contacts welded closed on the relay board
  • Limited airflow behind the oven
  • Resistance too high in the sensor leads or connectors
  • Oven started right after a very hot cycle

Can you keep using the wall oven with F2?

Do not keep using the oven after F2. Turn it off, keep the door closed, and let it cool completely, because a relay that has stuck closed can keep heating even when the control wants it to stop. If F2 returns after the oven has cooled, stop using it and leave it off until it is examined. Never restart it again and again to see whether the code clears.

What you can safely check

  1. Turn the oven off, keep the door closed and wait until it is completely cool.
  2. Look at the vent and the cabinet opening around the oven and clear anything in the way.
  3. Take foil or liners off the racks and the oven bottom.
  4. If F2 shows up again, do not use the oven, and contact us.

What our technician does for F2

  • Test the relay board contacts for sticking
  • Check airflow at the rear of the oven
  • Measure the sensor leads and connectors for extra resistance
  • Quote the repair after the cause is found

How to keep F2 from coming back

  • Keep the oven vent and the cabinet opening clear of anything that traps heat.
  • Do not cover racks or the oven floor with foil or liners, which can hold heat in.
  • Allow the cavity to cool fully before starting another long cycle.

Technical reference

Code
F2
Appliance
Monogram wall oven
Control family
Monogram ZET1 and ZET2 convection wall ovens (30-inch)
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

F2 questions

Why does F2 matter more than other sensor codes?

It means the oven read a temperature above its limit, and a stuck relay can keep the heating on. That is why we do not suggest restarting it repeatedly.

Does a self-clean cycle trigger F2?

A latched self-clean has a higher limit of 915 degrees F, so a normal clean should not trip it. F2 appears when the sensor reading goes past the limit for the mode in use.

Could my cabinet cause F2?

It can contribute. Limited airflow behind the oven is a documented cause, so a blocked vent or a tight cabinet opening is worth checking while the oven is cold.

Is F2 the same as an open or shorted sensor code?

No. Those codes describe the sensor circuit reading too high or too low in resistance, while F2 reports that the oven actually read hot. Extra resistance in the sensor wiring is one named cause of F2, so the two can be related.

Will F2 clear after the oven cools?

The code may stop showing, but the cause is still in the oven. A stuck relay or blocked airflow will bring F2 back on the next hot cycle, so a cooldown is not a fix.

Need help with F2?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair