(813)750-0388 Book a Repair
Monogram wall oven error code

Monogram Oven F6: Control Board A/D Converter Failure

F6 on a Monogram oven means the analog-to-digital converter on the control board has failed. That core part translates sensor readings, so the board itself is the problem.

Needs attention soonChecked November 2026

What does Monogram wall oven code F6 mean?

F6 is a failure of the analog-to-digital converter on the oven's control board. That part translates sensor readings into digital values the board can use, so when it fails, the board can no longer read the oven's sensors reliably. The problem sits in the board itself, not in a switch or sensor you could test in the field. No other part is named as the cause.

F6 at a glance

Code
F6
Appliance
Monogram wall oven
Applies to
Monogram oven electronic control board
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The A/D converter part on the control board has failed

What you may notice with F6

  • F6 shows on the oven display
  • The oven will not heat or hold its settings as expected
  • The code stays after you restart the power

How the wall oven detects F6

An oven's sensors, such as the temperature sensor in the cavity, produce analog signals. The control board cannot use those signals directly, so a converter on the board turns them into digital numbers the board's processor can read. Everything the oven decides about heat depends on those numbers.

F6 means the converter itself has failed. It is a core part of the board, so the oven cannot interpret its sensors, and the board reports the error. This is different from a sensor failing, where the board can still tell something is wrong with that one input. A converter failure affects the board's whole ability to read inputs. It is also why the fix is replacing the board and not adjusting or replacing individual sensors or switches.

Likely causes of F6

  • The A/D converter part on the control board has failed
  • The board needs replacing because that part cannot be repaired separately

Can you keep using the wall oven with F6?

Do not use the oven while F6 is showing. The control board cannot read its sensors correctly, so it cannot be trusted to manage heat. Turn the oven off and switch off the breaker if you are leaving it unused for a while. Leave the panels closed; nothing about this code can be fixed safely by the owner.

What you can safely check

  1. Turn the oven off and switch off its breaker.
  2. Do not open any panel, since there is no safe owner step for a board-level part.
  3. Restore power once to see whether F6 shows again.
  4. If it does, leave the oven off and call us.

What our technician does for F6

  • Confirm the A/D converter failure on the control board
  • Replace the control board
  • Test the oven's operation after the new board is in place

How to keep F6 from coming back

  • Florida storms bring surges that can stress electronics, so consider whole-home surge protection for the oven circuit.
  • After a power outage, wait for steady power before turning the oven back on.
  • Keep the area around the control panel dry and ventilated so the electronics are not exposed to steam or moisture.

Technical reference

Code
F6
Appliance
Monogram wall oven
Control family
Monogram oven electronic control board
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

F6 questions

What is an A/D converter?

It is a part on the control board that turns sensor signals, which are analog, into digital values. Without it, the board cannot read the oven's sensors correctly.

Can F6 be fixed by replacing a sensor?

No. The code points to the board itself, not a sensor or switch you can test in the field. Replacing a sensor would not address the converter.

Will a power restart fix F6?

A restart can show whether the code returns, but a failed converter part does not repair itself. If F6 stays, the board needs replacement.

Is F6 caused by a bad sensor?

No. F6 is a failure inside the control board, in the part that translates sensor readings. A bad sensor would be reported separately, so replacing one would not remove the F6 code.

Is replacing the board the only fix?

For F6 the converter part has failed on the board itself, and the board is not repairable without replacement. That is why the work is a board swap rather than a sensor or switch test.

Need help with F6?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair