(813)750-0388 Book a Repair
Monogram wall oven error code

Monogram ZET Wall Oven F4: Shorted Oven Temperature Sensor

When a Monogram ZET wall oven stores F4, the control reads the oven sensor as shorted, below 950 ohms. The code stays hidden, so you notice uneven heating or early shutoffs.

Needs attention soonChecked November 2026

What does Monogram wall oven code F4 mean?

Monogram convection wall ovens in 30-inch single or double form, from the ZET1 and ZET2 series, for example the ZET1PL1SS and ZET2SL1SS, store F4 when the oven sensor reads as shorted. A shorted sensor measures below 950 ohms, where a healthy one sits near 1,080 ohms at room temperature. These ovens hide F4 from the display and show only F9 to the owner. The signs are heating that is uneven, a shutoff that comes early, or a bake that will not run.

F4 at a glance

Code
F4
Appliance
Monogram wall oven
Applies to
Monogram ZET1 and ZET2 wall ovens, shorted sensor reading
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Sensor that has shorted internally

What you may notice with F4

  • The oven heats unevenly during a bake
  • A bake shuts off earlier than it should
  • The oven refuses to start a bake
  • The display does not mention F4 at all

How the wall oven detects F4

A sensor in the cavity gives the control a resistance that stands for the temperature. At room temperature the healthy value is close to 1,080 ohms, and the control treats a reading under 950 ohms as a short.

When the reading drops below that line, F4 goes into the stored history instead of the display, because only F9 is shown to owners on these ovens. A short can be inside the sensor or in a lead whose insulation has worn or been pinched against metal. Either way, the control loses a reliable view of oven heat, which explains uneven baking and early shutoffs. A circuit test separates the sensor from its wiring, and the stored history confirms the code.

Likely causes of F4

  • Sensor that has shorted internally
  • Sensor wire pinched against the metal
  • Worn insulation on the sensor wiring
  • Relay board misreading the sensor signal

Can you keep using the wall oven with F4?

You can try a short bake to see whether the oven still heats, but do not trust it for a long or important cook. When the control cannot read the temperature, it may shut off early or run unevenly, and a pan left in an oven you cannot judge is a poor risk. If the oven misbehaves again, turn it off and leave it until it is tested.

What you can safely check

  1. Turn the oven off, leave the door shut and let the cavity cool.
  2. Clear away any pan or foil resting against the rear of the oven interior.
  3. Run a short bake and see whether it heats and holds its temperature.
  4. If it still misbehaves, contact us and describe what the oven did.

What our technician does for F4

  • Run a circuit test to see whether the short is in the sensor or its lead
  • Look for pinched or damaged sensor wiring
  • Read the stored history to confirm F4
  • Check the relay board's sensor input last

How to keep F4 from coming back

  • Keep pans and foil clear of the back wall so the sensor wiring is not pressed or pinched.
  • Avoid pushing racks hard into the rear of the cavity.

Technical reference

Code
F4
Appliance
Monogram wall oven
Control family
Monogram ZET1 and ZET2 wall ovens, shorted sensor reading
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

F4 questions

Why does the oven hide F4 but show F9?

On these ovens only F9 is meant for the owner's display, and the other codes stay in memory. A technician reads F4 from the stored list.

What does a shorted sensor do to baking?

The control gets a resistance well below its healthy value, so it cannot judge the real temperature. That is why heating turns uneven, or the oven stops early or refuses to run.

Could the wiring be the cause instead of the sensor?

Yes. A lead pinched against metal or with damaged insulation can short the circuit, and a test tells the two apart.

Is F4 the same as F3?

No. F3 is an open sensor reading and F4 is a shorted one. Both leave the control without a trustworthy temperature, but the circuit is broken in opposite ways.

Does F4 mean I need a new oven?

No. The cause is the sensor or its wiring, and both are repairs. The sensor and leads are tested first, and the relay board is considered last.

Need help with F4?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair