(813)750-0388 Book a Repair
Monogram wall oven error code

Monogram ZET Wall Oven F8: EEPROM Memory Data Error

F8 on a Monogram ZET wall oven is a stored memory error. The control could not save or read its settings, and a repeat points to the logic board.

Needs attention soonChecked November 2026

What does Monogram wall oven code F8 mean?

Monogram's ZET1 and ZET2 line of 30-inch convection wall ovens, in single or double versions like the ZET1PL1SS and ZET2SL1SS, records F8 when the control cannot store or read its saved settings correctly, an EEPROM data shift failure. A repeat points toward the logic board. The code is hidden from the display, and it is not the door latch problem, which has its own code, FC. You might see the oven lose its settings, behave oddly, or fail to run a program.

F8 at a glance

Code
F8
Appliance
Monogram wall oven
Applies to
Monogram ZET1 and ZET2 wall ovens, control memory (EEPROM)
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control memory that stored a setting wrongly

What you may notice with F8

  • The oven clock resets itself unexpectedly
  • A program or setting you entered is gone
  • The oven acts oddly and stops following commands
  • Nothing about F8 shows on the display

How the wall oven detects F8

Inside the control sits a small memory chip, an EEPROM, that holds the oven's saved settings. Whenever the control stores something, it shifts the data into the chip, and when it needs the information back, it shifts it out.

F8 is stored when that shifting does not complete correctly. One incident can follow a brief power disturbance, so the control is not judged on a single event. A repeat, though, suggests that the memory on the logic board is no longer reliable, and replacing the board is the documented next step. F8 never appears on the display on these ovens, so a lost clock, a forgotten program, or an oven that stops following your program is how it shows up. The door latch has a separate code.

Likely causes of F8

  • Control memory that stored a setting wrongly
  • Power disturbance in the middle of a save
  • Logic board memory wearing out
  • Memory error repeating on an aging board

Can you keep using the wall oven with F8?

After a single memory glitch the oven may work normally, so you can use it with attention. If settings keep disappearing or the oven stops following what you enter, do not rely on it, because a control that cannot hold its programming may change or end a cycle unexpectedly. Turn it off when you leave the room, and note when the problem returns.

What you can safely check

  1. Turn the oven off at its controls and give it a few quiet minutes.
  2. Enter the time of day and a basic bake, then watch whether both are accepted.
  3. Write down whether settings vanish again.
  4. If they do, contact us and tell us how often.

What our technician does for F8

  • Read the stored history to see whether F8 repeats
  • Rule out a power disturbance
  • Replace the logic board only when the memory error repeats

How to keep F8 from coming back

  • Avoid switching the oven breaker on and off repeatedly, since each interruption can break a save in progress.
  • During a Florida thunderstorm or after an outage, wait a few minutes before setting the oven again.

Technical reference

Code
F8
Appliance
Monogram wall oven
Control family
Monogram ZET1 and ZET2 wall ovens, control memory (EEPROM)
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..

FAQ

F8 questions

Why does my oven forget the clock?

A clock that resets can go with F8, since the control saves its settings in memory and could not store or read them correctly. A single reset after a power flicker is less telling than a repeat.

Does a repeat of F8 need a new board?

A repeat is the case where the logic board becomes the part to look at. Before that, we read the stored history and rule out a power disturbance.

Will the oven still cook with F8?

It may, if the settings it holds are intact, but a control that cannot store data correctly may drop a program midway. Watch it closely and avoid long unattended cooks.

Can F8 clear without any repair?

It can after a single power disturbance, because the memory write may simply succeed the next time. A repeat is a different matter and points toward the logic board.

What helps you decide whether F8 is a one-time event?

Notes on when settings disappeared, how often, and what the oven was doing. Together with the stored history, those dates show a pattern, so a board is not replaced for a one-off upset.

Need help with F8?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813)750-0388 Book a Repair