Monogram Oven F1: Cavity Temperature Sensor (RTD) Error
F1 on a Monogram oven means the control board is not getting a valid signal from the RTD temperature sensor inside the cavity. Testing it is a technician job.
What does Monogram wall oven code F1 mean?
With F1, the oven's control board cannot get a valid reading from the RTD temperature sensor inside the cavity, which is a general oven-sensor problem. The oven needs that reading to know how hot it is. Either the sensor itself, the wiring harness connection to it, or the board's input circuit for the sensor has failed, and it takes a resistance test with the oven de-energized to tell which.
F1 at a glance
- Code
- F1
- Appliance
- Monogram wall oven
- Applies to
- Monogram oven with RTD cavity temperature sensor
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A cavity sensor that has stopped working
What you may notice with F1
- F1 appears on the display and the oven will not heat normally
- Preheat does not complete as it normally does
- The code returns after power is cycled at the breaker
How the wall oven detects F1
The temperature inside a Monogram oven is watched by an RTD sensor in the cavity. Its electrical resistance changes in a known way as it heats up, and the control board converts that into a temperature. The board uses the number to switch heating elements on and off.
F1 appears when the board is not getting a reading it can trust. The sensor may have failed. The wiring that carries its signal to the board may have a bad connection. Or the part of the board that receives the signal may have failed. From the display you cannot tell the three apart, and because the board is blind to cavity temperature, it stops relying on that reading and reports the error. Testing the sensor means measuring its resistance with the oven de-energized.
Likely causes of F1
- A cavity sensor that has stopped working
- A broken connection in the sensor's wiring harness
- A failed sensor input circuit on the control board
Can you keep using the wall oven with F1?
Stop baking with the oven while F1 is showing. Without a valid reading, the control board cannot regulate cavity heat, and you cannot tell what temperature the oven is really at. Switch it off at the breaker if you are leaving it unused until it can be tested. Do not poke at the sensor inside the cavity.
What you can safely check
- Turn the oven off, switch off the breaker and let the cavity cool completely.
- Look inside, without touching the sensor, for anything resting against it.
- Restore power and see whether F1 comes back.
- Do not test or bend the sensor; call us if F1 returns.
What our technician does for F1
- Test the sensor resistance with the oven de-energized
- Inspect and test the sensor's wiring harness connection
- Check the control board input for the sensor and replace the part that failed
How to keep F1 from coming back
- Keep pans and racks from knocking the sensor when you slide food in and out.
- Clean the cavity when cool and avoid spray near the sensor and its wiring opening.
- A power surge from a Florida storm can stress the board, so consider surge protection on the oven circuit.
Technical reference
- Code
- F1
- Appliance
- Monogram wall oven
- Control family
- Monogram oven with RTD cavity temperature sensor
- Maker documentation
- Monogram owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Haier US Appliance Solutions, Inc..
Related Monogram wall oven error codes
F1 questions
Why can't I just test the F1 sensor myself?
It is mounted inside the cavity, and measuring its resistance needs access with the oven de-energized. Doing it without the right approach can damage the wiring.
Is F1 the same as an oven that runs too hot?
Not exactly. F1 says the control board is not getting a valid reading, so it cannot regulate heat properly. Stop baking until the sensor is tested.
What is an RTD?
It is a resistance temperature detector, the sensor that reports cavity heat to the control board through changes in its electrical resistance. The board turns that signal into a temperature.
Will F1 clear after a restart?
A restart might clear a one-off glitch, but F1 returns when the sensor, its wiring or the board input is actually failing. If it comes back, stop using the oven.
What should I describe to the technician about F1?
Say when the code showed up, whether the oven was heating, and whether anything near the sensor was bumped or cleaned. That tells them where to begin their resistance test.
Need help with F1?
We trace the cause in your home first and write the price down before any part is swapped.